Canon C450 battery grip User manual

C450D Battery Grip
                       For Canon EOS 450D

fifl CaSOD Battery Grip Instruction For Usage

r Parts of C450D Battery Grip
O Protective cover                 @ Verticafgrlp <ON>/<OFF> switch
@ Electrical contacts                @ Vertical-grip shutter button
@ Attachment screw                 @ Camera battery compartment cover slol
@ Guide pin                    @ Vertical-grip Main Dial
@ Attach/detach knob                @ Hand strap mount
@ Battery magazine lock lever           @ Tripod socket
@ Battery magazine release handle        @ Baftery magazine protective cover
@ DC cord hole                  @ Battery magazine (for LP-ES)
@ Vertical-grip aperture/exposure compensation bufton @ Battery pack compartment
@ Vertical-grip AF point selection/Magnify button  @ Battery magazine (for size-AA bafteries)
 @Vertical-grip AE locUF E locUlndex/Reduce  button
Thank you for purchasing a C450D Battery Grip for Canon EOS 450D
The C450D battery grip is a battery grip that can hold two Battery Pack LP-ES or six size-AA bafteries.  lt is also   .
equipped with a vertical-grip shufter button, Main Dial, etc. to enable shooting in the same way as a horizontal grip..
 r Attaching to the Camera 1. Remove the battery from the camera. (Fig.1)                               lpu,w, fuj/tos' 's
 2. Pull out the camera's battery compartment cover at a slanted angle to remove. (Fig.2)
   Perform over a table so that the camera does not drop.
    Insert the detached cover into the storage slot (Fig.3)
 3. Remove the protective cover, and then insert the electrical contacts into the camera baftery
   compartment. 1Fig.a-O)
 4. Align the attachment screw with the camera's tripod socket, and then tum the attach/detach knob
    to tighten securely. (Fig.a-@)
b. Po not further prstr open
    damage  its hinge.
      . Be sure to attach the battery grip to the camera before inserting the batteries. The results of the battery check
 -  may not be displayed properly  if you aftach the battery grip to the camera with the batteries already inside.
      . Before removing the battery grip from the camera, be sure to turn the camera's power switch to <OFF>, and
     take out the batteries. After removing the batteries, attach the protective cover to the electrical contacts.
 r  Installing the Baftery Packs
 1. Press down the lock lever to flip out the release handle, turn  it as shown by the arrow, and then pull out the
    battery magazine (for size-trA batteries). (Fig.5)
 2. Insert one or two Battery Pack LP-ES into the battery magazine (for LP-ES). (Fig.6)
 3. Remove the protective cover of the battery magazine, and then aftach to the battery grip. (Fig.7-1)After aftaching,
   check that the baftery magazine is securely attached to the battery grip.
 4. Close the release handle.(Fig.7-2)
   The camera will not work unless the handle is closed.
O  tf storing battery magazine separately, be sure to                                                        "i
 151 .  lf only one battery pack is used, it may be insert in either the right or left sides.                             1 r    . lf two battery packs are inserted. Power is supplied simultaneously by both battery packs. TWo battery packs
      with different charging levels can be inserted and used without any problems.                                         !d
 r Inserting size-AA Batteries
  1. Insert the bafteries into battery magazine (for size-AA bafteries). (Fig.8)
   Make sure the + and - battery contacts are properly oriented as shown in the illustration.
  2. Aftach the battery magazine into the battery grip. (Fig.9-1)

After attaching, check that the battery magazine is securely attached to the battery grip.
         3. Close the release handle. (Fig.9-2)
        The camera  will not work unless the handle is closed.
   $  . fewer images can 6U$rbtwtren uslng
       .     . recommendedWith size-M batteries,only for emergencies.use six new batteries of the same brand at temperatures above 20'C168'F. The   $
   R  camera may not function when used in low temperatures or old and new batteries are used together.
      r Using a Household Power Outlet
       To connect to a household power outlet, use theAC Adapter kitACK-ES (sold separately).
         1. Connect the power cord to the AC adapter, and insert the prongs into a power outlet. Connect the
      DC cord to the DC coupler. (Refer to ACK-ES Instructions)
        2. Insert the DC coupler into the release-handle-side baftery pac* compartment of the battery magazine (for LP-ES).
       And then attach to the battery grip. Pass the DC cord through the DC cord hole. (Fig.l0)
   Q  . Always set the camera's power switch to <OFF> before disconnecting the power cord.
     *    . B" careful that the DC cord does not get pinched between the battery grip and lhe battery magazine.
     r Using the Battery Grip
            . Turning the verticalgripcON>/<OFF>  switch to <ON> (Fig.11) makes the battery grip buttons and dial function in
        the same way as those on the camera.
           . When shooting in the horizontalgrip position, tum the verticalgrip <ON>/<OFF> switch to <OFF> so that you do
        not accidentally use the buttons or dial on the battery grip.
          . Hand strap E-1 (sold separately) can be used for enabling a more secure grip.
     r Gaution
          . Remove the battery packs/batteries from the battery grip when the camera will not be used for an extended period.
          . Never attempt to disassemble or repair the product yourself. Any malfunction or accident resulting from such
       ..3ction is not covered by the wananty.
      I  Baftery Life
     Temperature: +23'Cl0"C 73"F132"F (Number of shots . approx.)
      Model                           Battery             No flash        50% flash
    EOS DIGITAL REBEI.         LP-E5x2             1200/1000          1000/800
     XS|/EOS 45OD         Size AA alkaline batteries      500/200          3m/100
                                      (Camera            Live             View                     shooting,                               on                                  CIPA                          based                                      & lmaging                                                              Products                                                                            Association)                                                                                                 testing standads.I       .. TheNo         number                      of                   images that                             can                                be                                         shot                                                                 is reduced                                                       by frequent                                                           usage                                                                                           of the LCD monitor,t                                                                                               holdingj      the shufter button halfiray down for an extended time, and using the AF frequently without shooting.
f        . The remairying battery level can be checked on the LCD monitor of the camera.'     I  Specifications
      Type:            Battery grip for the EOS DIGITAL REBEL XS|/EOS 450D
    Baftery:     (1) Battery pack LP-ES
                           (2) Six size-AAAlkaline  batteries
                           (3) AC Adapter kit ACK-ES
     Power switch: Camera's power switch
    Dimensions: 129.2(W)x103.1(H)x79.9(D) mm/ 5.1(W)x4.1(H)x3.1(D)  in
   Weight:    Approx. 230918.1o2. (without batteries and battery magazine)
       . All the specifications above are based on Canon's testing standards.
      . The products specifications and exterior are subject to change without notice.                                www.butkus.us

i e+-*:i-                                 : }biF;gE.#ii+'4.r.:.  .          -.              {f,Eq*                                                     ,.e.+ili