Film cameras
Wirgin Edixa User manual
User manual for Wirgin Edixa. 7 pages in English. Read the original PDF, download or print a copy without registration.
7 pagesEnglish1.2 MB PDF
Loading your manual…Open PDF directly
Document details
- Brand
- Wirgin
- Model / document
- Wirgin Edixa
- Document type
- User manual
- Language
- English
- Pages
- 7
- File size
- 1.2 MB
- Category
- Film cameras
- Document date
- Not specified in catalog
Search available document text
Find a term, then jump to its page in the original PDF. Image-only pages may not be searchable; check the PDF for exact wording and diagrams.
Page 2 · Read text
INTRODUCTION
The Edixa Reflex is a single lens reflex camera which uses 35-mm film, both color and black and
white. The picture size is 24 x 36 mm or approximately 1 x 1 1/2 inches. A wide variety of
emulsions and speeds are available in 20 and 36 exposures daylight film cartridges.
The Edixa Reflex offers you all the latest innovations of photographic progress - including focal
plane shutter with speeds from 1 second to 1/1000th, coupled film transport and shutter winding,
double exposure prevention, automatic and preset diaphram lenses, interchangeable lenses,
interchangeable viewfinders, single lens reflex optical system, freedom from parallax, prism
viewfinder, flash synchronization for flash bulbs and electronic strobe units, rapid lever wind for
sequence pictures, and many other outstanding features.
Also with the Edixa Reflex you have available a
microscope adapters, bellows extensions, and
choice selection of Wide Angle and Telephoto
many other accessories are available too. Write
lenses ranging from 28-mm. to 1000-mm. focal
to our distributor for complete price list.
length and as fast as f/1.5. Extension tubes,View original page 2Page 3 · Read text
Successful photographic results depend largely following the instructions for the use of the
upon the careful operation and handling of your camera in the pages which follow. After you
camera. It is advisable therefore, to first practice have gained the full knowledge of its operation,
using the camera without film, you may start to take pictures.
INSERTING THE FILM
To open the camera back, pull the latch (1)
outwards. Pull out rewind knob (3). Place the
fresh film cartridge into the empty film chamber
(4) with the film leader in the direction of the
take-up spool (7). Push the rewind knob down,
thus engaging the film cartridge. Pull the film
from the cartridge and place the tongue into the
slit of the take-up spool (7). Then turn the take-up
spool by hand without using the lever, wrapping
some film around the spool.
Be sure that the teeth on the sprocket wheel (6) engages both top and bottom rows of perforations
on the film, before closing the camera back, and see that the film lies evenly on the film track (
Close the back of the camera and pre latch down to secure. Turn lever fully, then set exposure
counter (10) direction of arrow) on number 36.View original page 3Page 4 · Read text
The indicator (exposure marker) is t triangle
engraved on the lever (8). Pre shutter release
button (9). Make two blank exposures by
winding lever and pressing shutter release
button The exposure counter will point to
exposure No. 1, and the camera is ready for
your first picture. You can be sure that the film
transports in your camera properly if the rewind
knob (3) turns counter clockwise as you turn
the lever (8) to the right.
TO OPEN & CLOSE WAIST-LEVEL FINDER
Press the small button on the back of the finder (on
back of camera) and it will open automatically. To
close, just press down any of the walls of the
finder till the cat( clicks To bring the magnifying
lens into position, press the small lever next to the
lens. The image viewed on the ground glass (after
you wind the shutter) will be reproduced on film,
in the same size. As you turn the focusing ring on
the lens, the image on the ground glass changes.
It will appear sharp. At the same time you are
composing your picture, and controlling the
depth of field. For critical focusing, use the
magnifier, keeping it close to your eye. Before
closing hood, be sure to fold the magnifier
down.
The waist level viewfinder can be interchanged with the Prism View Finder. To remove the finder
(waist-level or prism finder) from the camera, proceed as follows. Push buttons (13) outwards, the
finder will lift upwards and can easily be removed.View original page 4Page 5 · Read text
To install either finder into camera, insert the front end of the finder into the open groove (15) of
the view
finder section of the camera (on top of camera, 15) then push rear end down until it clicks into
position.
THE PRISM FINDER
The Prism Finder is used for eye-level focusing, holding
the ocular lens of the finder close to the eye. You see a
laterally correct, upright image for both vertical and
horizontal shots. The direction of movement seen in
the finder is the same as that of the subject. This
finder, therefore, is ideal for sport and action
photography (horse races, track meets, tennis matches
etc.) because you can move the camera in the same
direction as that of the subject. The Prism Finder can
be installed and removed from camera in the same way
as the Waist-Level Finder.
SHUTTER AND FILM TRANSPORT
The shutter winding and film transport are coupled, and
is done by winding the lever (8) fully until it stops,
therefore, there is no danger of double exposures. The
lever automatically snaps back to its neutral or normal
position. If you don't wind the lever fully (complete
rotation to the right), you won't be able to press the
shutter release knob. If this should happen, just
continue to wind the lever till the end. Please note: The
image appears on the reflex ground glass only after the
lever (8) is turned fully (complete rotation of lever to
the right).The shutter is released by pressing the shutter
release button (9).
Release gently to avoid blurring the picture.View original page 5Page 6 · Read text
TO SET THE SHUTTER SPEEDS
The speeds are set by means of adjusting knob (17) and the Knob
(18). The engraved figures on the Knobs (17) and (18) indicate
fractions of seconds: for example,50 means 1/50 of a second, 5
means 1/5 of a second etc.
EDIXA REFLEX S (Standard) with shutter speeds: 1/25 -
1/1000 of a second:
To set the shutter for the selected speed lift the setting
knob (17)- either before or after winding the shutter - and
turn it until the speed number is placed next to the red dot
on the inside of adjusting knob, and let knob drop down.
EDIXA REFLEX with shutter speeds:
1 sec. - 1/1000 of a second:
a) Fast speeds: To set the shutter for fast speeds, turn knob
(18) till the dot points to zero. Then lift knob (17) either
before or after winding the shutter, and turn it until the
speed number you select is placed next to the red dot on
the inside of Knob. (17), and let it drop down. For time
exposures use the setting "B" on Knob (17), be sure Knob
(18) is set on zero. Shutter will stay open as long as shutter
release button is pressed down (9). An Edixa Cable
Release with locking device should be used for time
exposures of long duration.
b) Slow Speeds: To set shutter for slow speeds lift Knob (17) and turn it until the the speed "25"
(1/25 of a second) is placed next to the red dot on the inside of Knob (17). Then turn Knob (18) to
the selected speed, (for instance 1 second.)
IMPORTANT: Before setting slow speeds always set the red "25" next to the red dot on the inside
of Knob (17).
FOCUSING, DIAPHRAGM, PRESET & AUTOMATIC LENSES
A separate instruction sheet is provided for standard lenses, preset diaphragm lenses and fully
automatic lenses, included with the lens.View original page 6Page 7 · Read text
FLASH SYNCHRONIZATION
The EDIXA-Reflex is fully synchronized for regular flashbulbs
and electronic flash. On
the front of the camera are two contact sockets. The top socket
(marked M on the side of the lens mount) is used for flashbulbs.
The bottom socket (marked X) is used for strobe and electronic
flash .
USE ELECTRONIC FLASH AND STROBE at 1/25th of a
second ONLY. See special instruction for use of flash bulbs.
UNLOADING FILM FROM CAMERA
After all the pictures have been taken, the film must be
rewound into the original cartridge. This is done by pressing
down on the button (26) located on the bottom of the camera,
and at the same time turning the rewind Knob (3) clockwise (to
the right). As long as film is still in the camera, you will feel the
effort of winding, which stops as soon as all the film is back in
the cartridge.
Then open back of camera (2), pull rewind Knob (3) upwards, and remove cartridge with exposed
film.
Film Reminder: On the rewind Knob (3) is an engraved scale (22) with speeds of most films. Set
this scale on the number corresponding to the speed of the film which you loaded your camera.
When you transport the film, watch the red dot on the rewind knob. When it turns counter
clockwise the film in your camera is loaded correctly. If it does not turn, the camera is either empty
or the film slipped out of the taking spool.View original page 7Related documents and language editions
From the M. Butkus archive. Original publisher and archive notices are retained.
Check the model and edition against your equipment.
PDF verified 2026-10-10.